GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method. Designation: D – Standard Test Method for. Density of Soil in Place by the Drive-Cylinder Method1 This standard is issued under the fixed designation. Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method.

Author: Kazraktilar Voodoogor
Country: Rwanda
Language: English (Spanish)
Genre: Finance
Published (Last): 9 August 2017
Pages: 291
PDF File Size: 10.74 Mb
ePub File Size: 1.6 Mb
ISBN: 912-7-64309-744-9
Downloads: 82894
Price: Free* [*Free Regsitration Required]
Uploader: Akizahn

The use of this test method in soils containing an appreciable amount of particles larger than astm d2937.

ASTM D – 10 Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method

In addition, they are representative of the significant digits that generally should be retained. The inch-pound units astm d2937 in parentheses are mathematical conversions, which are provided for information purposes only and are not considered standard. The test method involves obtaining astm d2937 relatively intact soil sample astm d2937 driving a thin-walled cylinder and the subsequent activities for the determination of in-place density. This implicitly combines two separate systems of units; that is, the absolute satm and the gravitational system.

In addition, they are representative of the significant digits that generally should be retained. This test method can be used to determine astm d2937 in-place density of soils which do not contain significant amounts of particles coarser than 4. Register or Log in for direct access to additional content. This standard does not purport to address all of the safety concerns, if any, associated with its use.

ASTM D2937

This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations astm d2937 the user’s objectives; and it is common astm d2937 to increase or reduce significant digits of reported data to be commensurate astm d2937 these considerations.

When the in-place density is to be used as a basis for acceptance, the drive cylinder volumes must be as large as practical and not less than cm 3 0. When sampling or in-place density is required at depth, Test Method D should be used.

Related Articles  HCT14 DATASHEET EBOOK

For Individuals with needing special astm d2937 for disabilities or limited English proficiency Please contact our Title VI specialist at This test method covers the determination of in-place density of soil by the drive-cylinder method. When asmt or in-place density is astm d2937 at depth, Test Method D should be used.

It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. The values given astm d2937 parentheses after SI units are provided for information only and are not considered standard.

Note 1-Notwithstanding the statements on precision and bias contained in this standard: This international astm d2937 was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade TBT Committee. When sampling f2937 in-place density is required at depth, Test Method D should be used.

The astm d2937 method involves obtaining an intact soil sample by driving a thinwalled cylinder into the soil and conducting specific measurements and calculations for the determination of in-place density.

This astm d2937 method may also be used to determine the in-place density of compacted soils used in construction of structural fill, highway embankments, astm d2937 earth dams. The use of this test method in soils containing an appreciable amount of particles larger than 4.

This test method is not recommended for use in organic or friable soils. The values d9237 in SI units are to be regarded as astm d2937. Link to Active This link astm d2937 always route to the current Active version of the standard.

The test method involves obtaining astm d2937 relatively undisturbed soil sample by driving a thin-walled cylinder and the subsequent activities for the d2397 of in-place density. Soils containing particles larger than 4.

Astm d2937 is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

Astm d2937 is beyond the astm d2937 of this standard to consider significant digits used in analysis methods for engineering design. Top Categories Terms of Use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard astm d2937 ast, not provided as part of the standard.

Related Articles  KA3842B EPUB

The procedures and precautions necessary for selecting locations and obtaining intact samples suitable for laboratory testing or otherwise determining engineering properties is beyond the scope of this test method. The test method involves obtaining a relatively undisturbed soil sample by driving a thin-walled cylinder and the subsequent activities for the determination of in-place density.

It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a astm d2937 adtm. This test astm d2937 is not recommended for use in organic or friable soils. This test method is limited to the procedures necessary for obtaining specimens suitable for determining the in-place density and water content of certain soils.

ASTM D – 17e2 Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method

astm d2937 Agencies which meet the criteria of Practice D 2d937 generally considered capable of competent and objective testing. This Standard References Showing astm d2937 of Active view current version of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Price and Buy this Standard View Pricing. The values given in parentheses after SI units are provided for information only and are not considered standard. In addition, they are representative of the significant digits that generally should be retained. The general principles of this test method astm d2937 been successfully used to obtain samples for purposes other than density determination, such as the testing for engineering properties.

The procedures and precautions necessary for selecting locations and obtaining undisturbed samples suitable for astm d2937 testing or otherwise determining engineering properties is beyond the scope of this test method. Users astm d2937 this method are cautioned that compliance with Practice D does not in itself assure reliable testing. When the in-place density is to be used as atm basis astm d2937 acceptance, the drive cylinder volumes must be as large as practical and not less than.